A restored "The Dorset"
- SeanM
- Tench
- Posts: 2643
- Joined: Wed Sep 14, 2011 9:28 pm
- 12
- Location: Bradford, West Yorkshire
A restored "The Dorset"
In May this year I bought an FT Williams the Dorset on Ebay for the princely sum of £15 including postage. The auction pictures gave the impression of a scruffy rod, but one of the correct length and without any obvious set.
On arrival the rod pretty much met up to my impressions of the pictures with the slight additional problem of the reel fitting being somehow jammed on the handle. Slightly more worrying was the damage to the cork that had been done by someone trying to unstick the reel fitting.
Here are some quick snaps I took on receipt:
I put the rod aside for a while until I had time to work on it. When I picked it up again a couple of months ago I was resigned to removing all the corks and making a new handle. After a bit of tugging and pulling I decided to try a bit of heat, reasoning that even if it didn't work I was going to remove the corks anyway. Surprisingly, after heating the it until whatever was under it began to smoke, I was able to pull the reel fitting off the handle. What had happened was that someone had wrapped the bottom of the handle with insulating tape and then pulled the reel fitting down over it - mighty strange!
The good news was that I was able to clean the cork up and, by altering the shape of the top of the handle slightly, remove much of the damage to the corks. One other strange thing was that the reel fitting didn't look right. If you look at the bottom picture above you'll see that the slit in the fitting is in the same plane as the reel would be when fitted. This means that the fitting won't grip the handle when tightened around the foot of the reel. I do wonder if this is why the insulating tape was applied, but why round the bottom of the handle?
I decided to have a play with the fitting to see if I could move the reel holder on the tube. After a bit of vice work I managed to move the fixed reel holder 90 degrees around the tube. I then refitted the fitting "upside down" so that the fixed bit was at the top putting the reel in a more modern position on the handle:
The rest of the restoration was pretty straightforward. I removed and re-glued the ferrules, tightened them up a bit and then blued them. I repaired the chipped FT Williams logo with a dab of green felt tip and I hand lettered the "de Luxe" as the transfer was beyond saving. I had a set of Bells Life rings from a MARCO Test and some bobbins of thread of approximately the right colour so off we went.
Here is the result:
I've got a bit of tidying up of the varnish (Ronseal Outdoor) to do before giving it a final coat. The thread is D grade, but that is close to the original and the colours have come out just right (I used banana oil to seal the whippings). The Bells Life rings are a good compromise on a rod like this as they are big enough to pass heavy line easily and they are better for float fishing than bridge rings.
These Dorsets are an under-rated rod. They are a better length than the Mark IVs and their clones for general fishing and they are more than powerful enough for barbel fishing on all but big rivers like the Trent. The cane is of excellent quality and there was no evidence of delamination on this example. I'm looking forward to giving the rod a good workout on some winter barbel at some point in the New Year.
On arrival the rod pretty much met up to my impressions of the pictures with the slight additional problem of the reel fitting being somehow jammed on the handle. Slightly more worrying was the damage to the cork that had been done by someone trying to unstick the reel fitting.
Here are some quick snaps I took on receipt:
I put the rod aside for a while until I had time to work on it. When I picked it up again a couple of months ago I was resigned to removing all the corks and making a new handle. After a bit of tugging and pulling I decided to try a bit of heat, reasoning that even if it didn't work I was going to remove the corks anyway. Surprisingly, after heating the it until whatever was under it began to smoke, I was able to pull the reel fitting off the handle. What had happened was that someone had wrapped the bottom of the handle with insulating tape and then pulled the reel fitting down over it - mighty strange!
The good news was that I was able to clean the cork up and, by altering the shape of the top of the handle slightly, remove much of the damage to the corks. One other strange thing was that the reel fitting didn't look right. If you look at the bottom picture above you'll see that the slit in the fitting is in the same plane as the reel would be when fitted. This means that the fitting won't grip the handle when tightened around the foot of the reel. I do wonder if this is why the insulating tape was applied, but why round the bottom of the handle?
I decided to have a play with the fitting to see if I could move the reel holder on the tube. After a bit of vice work I managed to move the fixed reel holder 90 degrees around the tube. I then refitted the fitting "upside down" so that the fixed bit was at the top putting the reel in a more modern position on the handle:
The rest of the restoration was pretty straightforward. I removed and re-glued the ferrules, tightened them up a bit and then blued them. I repaired the chipped FT Williams logo with a dab of green felt tip and I hand lettered the "de Luxe" as the transfer was beyond saving. I had a set of Bells Life rings from a MARCO Test and some bobbins of thread of approximately the right colour so off we went.
Here is the result:
I've got a bit of tidying up of the varnish (Ronseal Outdoor) to do before giving it a final coat. The thread is D grade, but that is close to the original and the colours have come out just right (I used banana oil to seal the whippings). The Bells Life rings are a good compromise on a rod like this as they are big enough to pass heavy line easily and they are better for float fishing than bridge rings.
These Dorsets are an under-rated rod. They are a better length than the Mark IVs and their clones for general fishing and they are more than powerful enough for barbel fishing on all but big rivers like the Trent. The cane is of excellent quality and there was no evidence of delamination on this example. I'm looking forward to giving the rod a good workout on some winter barbel at some point in the New Year.
Last edited by SeanM on Sat Dec 13, 2014 3:51 pm, edited 2 times in total.
Quot homines, tot sententiae.
- MGs
- Pike
- Posts: 6426
- Joined: Wed Nov 02, 2011 2:24 pm
- 12
- Location: Cornwall
Re: A restored "The Dorset"
Very nice. I agree much under rated. I don't own one but have waggled a few. Nice that you have kept to the original whipping colours
Old car owners never die....they just rust away
- Mark
- Head Bailiff
- Posts: 21217
- Joined: Mon Aug 22, 2011 4:55 pm
- 12
- Location: Leicestershire
- Contact:
Re: A restored "The Dorset"
Nice one Sean.
Mark (Administrator)
The most precious places in the English landscape are those secretive corners,
where you find only elder trees, nettles and dreams. (BB - Denys Watkins-Pitchford).
The most precious places in the English landscape are those secretive corners,
where you find only elder trees, nettles and dreams. (BB - Denys Watkins-Pitchford).
- Kingfisher
- Catfish
- Posts: 5772
- Joined: Sat Apr 07, 2012 4:14 am
- 12
- Location: Llandrindod Wells (Mid Wales)
Re: A restored "The Dorset"
Looks very nice Sean.
I'd love to have a waggle of one to see if it's like a Black Seal. Bob Roberts and Hermit had a waggle of my Black Seal and agreed it would be a lovely Barbel rod. I want a DoB Dorset next.
Full marks on the tidying up you've done, lovely job.
I'd love to have a waggle of one to see if it's like a Black Seal. Bob Roberts and Hermit had a waggle of my Black Seal and agreed it would be a lovely Barbel rod. I want a DoB Dorset next.
Full marks on the tidying up you've done, lovely job.
God never did make a more calm, quiet, innocent recreation than angling.
Izaak Walton
- SeanM
- Tench
- Posts: 2643
- Joined: Wed Sep 14, 2011 9:28 pm
- 12
- Location: Bradford, West Yorkshire
Re: A restored "The Dorset"
It's a more powerful rod than a Black Seal Matt. About the same in the tip, but thicker in the butt. The Dorset has quite a slow taper in the butt which carries the power into the middle section.
Quot homines, tot sententiae.
- AshbyCut
- Honorary President
- Posts: 10142
- Joined: Sun May 06, 2012 1:27 am
- 12
- Location: North Warwickshire
Re: A restored "The Dorset"
Well done, Sir.
"Beside the water I discovered (or maybe rediscovered) the quiet. The sort of quiet that allows one to be woven into the tapestry of nature instead of merely standing next to it." Estaban.
- Loop Erimder
- Wild Carp
- Posts: 9984
- Joined: Wed Apr 04, 2012 11:33 pm
- 12
- Location: Leicestershire
Re: A restored "The Dorset"
I have one too that was restored by LJM they are wonderful rods, I must use it sometime very soon
Chance is always powerful. Let your hook be always cast; in the pool where you least expect it, there will be a fish
- Michael
- Tench
- Posts: 2754
- Joined: Thu Oct 06, 2011 5:45 pm
- 12
Re: A restored "The Dorset"
Back from the dead one might say, well done Sean.....
- Gord
- Crucian Carp
- Posts: 787
- Joined: Mon Jul 02, 2012 10:57 pm
- 11
- Location: Romsey, Hampshire
Re: A restored "The Dorset"
a nice bit of work you have done on a nice rod, as its getting towards christmas i took my dorset out today as the version i have looks very festive with its red and green whipping and green hardware on the handle didnt catch a lot just nice to get out
when you are going through hell just keep on going (winston churchill)
- Nobby
- Wild Carp
- Posts: 10987
- Joined: Sun Oct 02, 2011 2:40 pm
- 12
- Location: S.W.Surrey
- Contact:
Re: A restored "The Dorset"
Perhaps a small sleigh-bell on the tip ring would be Ok for the run up to Xmas Day, Gord?
http://www.shockwave-sound.com/sound-ef ... glbell.wav
http://www.shockwave-sound.com/sound-ef ... glbell.wav