Same on the Eureka... but not the TriumphWallys-Cast wrote: ↑Thu Nov 26, 2020 1:30 pm A very nice stocking filler Mal. I love that Hardy check arrangement.
Wal.
The Hardy No. 2 Wallis Reel
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
Actually only the Wallis No.1 is a true pin and good runner. The No.2 reels are winches same as the Eureka reels so aren't as free running. I did mention in another thread about a Eureka 4" which had a boss same as a Conquest so ran better than those with a telephone latch and other members mentioned having seen a couple too.
- Silexman
- Ruffe
- Posts: 56
- Joined: Tue May 13, 2014 9:17 pm
- 10
- Location: Penang & Northumberland
Re: The Hardy No. 2 Wallis Reel
I've just done some testing of my Wallis reels and the results were:-
3.5" No 1 35 seconds
3.5" No 2 27 seconds
4" No 2 19 seconds
Tried the Triumphs too.
4" 16 seconds
3" 16 seconds
Might try it with Eurekas and Conquests too.
3.5" No 1 35 seconds
3.5" No 2 27 seconds
4" No 2 19 seconds
Tried the Triumphs too.
4" 16 seconds
3" 16 seconds
Might try it with Eurekas and Conquests too.
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
For spin tests centrepins should be horizontal and winches vertical
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
Sorry, what do you mean by Slater made ones?StefanDuma wrote: ↑Thu Nov 26, 2020 7:37 pm I love all the variations of the Wallis reels, the Slater made ones - still finding variations - plus the Hardy ones. There are more Hardy ones that I did not know existed. Trying to track down one owned by Wallis with a couple of variations in the construction.
The 3 1/2 inch model is rare and a great acquisition, well done.
I know several manufacturers made Wallis rods, but didn't know they made reels too!
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
The Hardy-Wallis reel in the first photo is a bit unusual. The earliest Wallis No.1 and no.2 reels had bulbous handles soon changed to the tapered type of handle to prevent line catching up on them as used on Conquests . Your straight handles must have come between the two mentioned.
- Catfish.017
- Eel
- Posts: 2237
- Joined: Wed Apr 04, 2012 8:53 am
- 12
- Location: Fradley Junction quite often!
Re: The Hardy No. 2 Wallis Reel
Excuse my ignorance chaps, but could someone enlighten me as to the difference between a pin and a winch?
- OhMyGoodness
- Bleak
- Posts: 142
- Joined: Thu Feb 04, 2021 5:18 am
- 3
Re: The Hardy No. 2 Wallis Reel
A true centrepin is like the aerial type or Rapidex etc. Which have a fine point at the tip of the main bearing shaft. This bears on a jewelled bearing in the drum centre cap (Silex or Wallis No.1 ) or a grub screw which can be adjusted for end float (Rapidex, Aerial, Speedia etc.)
These run best held horizontally.
A winch doesn't have a fine point or bearing cap in the drum. So the drum is usually retained by a nut or latch (Eureka, Wallis no.2, Longstone, modern bearing reels).
These winches tend to run less well than the true pins and are best held vertically.
These run best held horizontally.
A winch doesn't have a fine point or bearing cap in the drum. So the drum is usually retained by a nut or latch (Eureka, Wallis no.2, Longstone, modern bearing reels).
These winches tend to run less well than the true pins and are best held vertically.
- StefanDuma
- Grayling
- Posts: 516
- Joined: Sun Jan 29, 2017 6:11 pm
- 7
Re: The Hardy No. 2 Wallis Reel
David Slater made a number of Wallis reels The Wallis Pike reel in 3 sizes, The Wallis Zephyr and the Improved Wallis Zephyr in two sizes.OhMyGoodness wrote: ↑Mon Jun 20, 2022 6:08 amSorry, what do you mean by Slater made ones?StefanDuma wrote: ↑Thu Nov 26, 2020 7:37 pm I love all the variations of the Wallis reels, the Slater made ones - still finding variations - plus the Hardy ones. There are more Hardy ones that I did not know existed. Trying to track down one owned by Wallis with a couple of variations in the construction.
The 3 1/2 inch model is rare and a great acquisition, well done.
I know several manufacturers made Wallis rods, but didn't know they made reels too!
- Catfish.017
- Eel
- Posts: 2237
- Joined: Wed Apr 04, 2012 8:53 am
- 12
- Location: Fradley Junction quite often!
Re: The Hardy No. 2 Wallis Reel
Ok got it, many thanks.OhMyGoodness wrote: ↑Mon Jun 20, 2022 2:39 pm A true centrepin is like the aerial type or Rapidex etc. Which have a fine point at the tip of the main bearing shaft. This bears on a jewelled bearing in the drum centre cap (Silex or Wallis No.1 ) or a grub screw which can be adjusted for end float (Rapidex, Aerial, Speedia etc.)
These run best held horizontally.
A winch doesn't have a fine point or bearing cap in the drum. So the drum is usually retained by a nut or latch (Eureka, Wallis no.2, Longstone, modern bearing reels).
These winches tend to run less well than the true pins and are best held vertically.