Making a traditional "Bell" plummet

Made some other form of traditional fishing tackle.
User avatar
Watermole+
Chub
Posts: 1040
Joined: Thu Mar 15, 2012 11:07 pm
12
Location: Devon & Cornwall border

Making a traditional "Bell" plummet

Post by Watermole+ »

As promised, here is how I made the traditional plummets, using the old Myford lathe with the help of the vertical slide attachment.
If you are only making one for yourself, it could be done with hacksaw and file.

The first thing was to sort out the material, in this case, all my offcuts of 5/8" copper and brass...

Image

The next step was to clean it up, face off one end and cut it into lengths of 5/8"..

Image

I am making these as a batch..

Image

The compound slide was then removed from the lathe and the vertical slide substituted..

Image

With a 5mm milling cutter, a 3/16" deep slot was cut in to each piece..

Image

All ready for the next ops..

Image

Now you have to turn these to the traditional bell shape.
The problem now, is that you have to cut very close to the end, which only gives you about 1/8" to hold on! The answer was to quickly turn up an aluminium holder that you can grip in the chuck jaws..

Image

Be very careful when you do this. Copper is a very ductile material and "grips" at the slightest provocation. The first thing you will know is when it suddenly comes flying out of the chuck, wrecking itself-and your holder in the process....So be warned..take only light cuts of no more than say 0.030" deep...

Image

When all are done, make the little loops by bending some 1/16" brass wire with round-nosed pliers like this..

Image

Next, I drilled the holes for the wire loops. I used a 1.7mm drill to firstly allow for spacing error and secondly, to allow a gap for the solder to run into..

Image

When the holes were drilled-and again, be careful that your drill does not "bite" in the copper...keep the speed down! ..the loops were soldered in place..

Image

After soldering, they were washed well in warm, soapy water to neutralize the acid and cleaned up..

Image

Time to cork up.

I firstly cut some slices of cork..

Image

...and sanded them down to thickness. I made mine 1/2mm over thickness to make a good, tight fit, then cut them into lengths and sanded them flat.

Image

Don't forget to put a little chamfer in the top inside corners.
Now they were pushed into place with a spot of glue..

Image

...and allowed to dry.

Image

After which, the ends were trimmed off and here we are..all ready to use!

Image

Hope that you liked that!

I will be posting them off to you as soon as the ordered mailing bags arrive..

Kind regards,

wm+

"Are not two sparrows sold for a farthing? Yet one of them shall not fall without your Father knoweth" ..Jesus of Nazareth, King James AV

User avatar
LuckyLuca
Barbel
Posts: 4792
Joined: Mon Jul 02, 2012 10:20 am
11
Location: Oxfordshire

Re: Making a traditional "Bell" plummet

Post by LuckyLuca »

Superb WM. Simple beauty, beautifully made!
I walked across an empty land
I knew the pathway like the back of my hand
I felt the earth beneath my feet
Sat by the river and it made me complete.

User avatar
Loop Erimder
Wild Carp
Posts: 9984
Joined: Wed Apr 04, 2012 11:33 pm
11
Location: Leicestershire

Re: Making a traditional "Bell" plummet

Post by Loop Erimder »

Wow......amazing

If there are any spare.......
Chance is always powerful. Let your hook be always cast; in the pool where you least expect it, there will be a fish

User avatar
Keston
Tench
Posts: 2585
Joined: Sun Feb 08, 2015 5:48 pm
9
Location: Fareham on the sunny south coast .

Re: Making a traditional "Bell" plummet

Post by Keston »

How fabulous , thank you so much for sharing how you made these lovely plummets.
John

User avatar
Wallys-Cast
Pike
Posts: 6579
Joined: Tue Mar 20, 2012 11:02 am
12
Location: Durham.

Re: Making a traditional "Bell" plummet

Post by Wallys-Cast »

A great tutorial on how to make lovely looking plummets.

Looking forward to seeing what's next.

Wal.

User avatar
Bob Brookes
Zander
Posts: 3654
Joined: Sun Oct 23, 2011 6:54 pm
12
Location: Nottinghamshire

Re: Making a traditional "Bell" plummet

Post by Bob Brookes »

Well made and very well described. I enjoyed that a lot WM+.
"You do not cease to fish because you get old, you get old because you cease to fish"

User avatar
CrayCane
Chub
Posts: 1017
Joined: Sun Apr 08, 2012 2:43 pm
11
Location: Bexley, Kent

Re: Making a traditional "Bell" plummet

Post by CrayCane »

Each one a little gem, marvellous.
Pete

User avatar
Muscavado
Grayling
Posts: 633
Joined: Thu Sep 08, 2016 6:22 pm
7

Re: Making a traditional "Bell" plummet

Post by Muscavado »

It's amazing how WM turns such a mundane item as a Plummet into a thing of beauty

I wish that I had known him in the 60's, I would have introduced him to one of my girlfriends....... :Chuckle:

John

User avatar
RBTraditional
Catfish
Posts: 5653
Joined: Thu Nov 10, 2011 1:10 pm
12
Location: Rural Kent
Contact:

Re: Making a traditional "Bell" plummet

Post by RBTraditional »

Absolutely superb!
" Angling is not an escape from life, but often a deeper immersion into it..."

https://thepiscatorialraconteurs.co.uk/

Paul D

Re: Making a traditional "Bell" plummet

Post by Paul D »

Miniature works of art, quite wonderful :Hat:

Post Reply

Return to “Making Other Items of Traditional Fishing Tackle”